Adress:Weihai Road, Jing'an District, Shanghai

s355mc steel maxium hardness

Contact us

Material Properties of S355 Steel - An Overview

Aug 23, 2015 · S355 is named based on it's minimum yield strength of 355 Mpa (N/mm2), However the yield strength reduces when you go up in thickness above 16 mm for flat products & hollow sections. Here is the table showing reduction in yield strength based on thickness. Up to 16 mm - 355 Mpa. 16 mm < t ≤ 40 mm - 345 Mpa.

Reply

S355MC - salzgitter-flachstahl.de

These steel grades can be welded both manually and using automatic equipment by means of all electrical welding process-es provided the general technical rules are observed. No major hardness increases appear in the heat-affected zone. Preheat-ing is not necessary under normal welding conditions and down to workpiece tem-peratures of +5 °C.

Reply

S355MC steel

Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. S355MC can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.

Reply

High Strength Low EN 10149-2 S355MC Steel Plate Supplier

Marc Steel is a well-known exporter and trader of EN 10149-2 S355MC Plates, which has a number of outstanding features to provide like having high durability, robust construction, precise dimension and more. EN 10149-2 S355MC Plates Buy High Tensile Plates EN 10149-2 S355MC

Reply

S355MC - salzgitter-flachstahl.de

2) The maximum content of Nb+V+Ti shall not exceed 0.220%. 3) If agreed in the order, the sulphur content is 0.0 0% max. ) The tensile test values given in the table apply to longitudinal samples. 2) It applies to nominal thickness ee < 3 mmA80 e ≥ 3 mmA5

Reply

EN 10149-2 S355MC steel steel,EN 10149-2 S355MC steel

Material #1.0976 Main chemical composition in EN 10149-2 S355MC steel is carton max 0.12, silicon max 0.50, manganese max 1.5, phosphorus max 0.025, Sulphur max 0.02. Shanghai katalor industry CO. Will return you with high-quality products

Reply

Structural Steel - S235, S275, S355 Chemical Composition

May 11, 2012 · Please use one of the following formats to cite this article in your essay, paper or reportAPA. Gilbert, Nick. (2020, February 20). Structural Steel - S235, S275, S355 Chemical Composition, Mechanical Properties and Common Applications.

Reply

S315MC / 1.0972 - SteelNumber - Chemical composition

Steel Chemical composition of steel S315MC (1.0972), Standards of steel S315MC (1.0972) Mechanical Properties of steel S315MC (1.0972) Equivalent grades of steel S315MC (1.0972) steel S315MC (1.0972) Tensile Strength, Elongation, Proof strength , Hardness

Reply

EN 10297-1 Grade E355 Carbon Steel Seamless Tubes –

Aug 12, 2015 · EN 10297-1 Grade E355 Tubes are low-cost Low Carbon Steel Tubes with max 022 % carbon content with combination of max 160 % manganese easy to form and shape .These pipes are manufactured as per EN Specification and commercially referred as cs pipes or ms pipes.Low Carbon Steel Pipes are not as hard as hig carbon steel pipes,Though carburizing can increase its surface

Reply

High Speed Steel Tool Steel O1 O1 Technical Data

O1 Tool Steel. O1 Tool Steel is the original oil-hardening, “non-shrinking” tool steel that can be hardened to the Rockwell C 65 range from a low austenitizing temperature. O1 is a general-purpose tool steel that is typically used in applications where alloy steels cannot provide sufficient hardness, strength, and wear resistance.

Reply

D2 Steel D2 Technical Data - Tool Steel High Speed Steel

For maximum wear resistance, temper between 300-350°F (149-177°C) for a hardness of 62-64 HRC. For the optimal balance between wear resistance and toughness, temper between 500-550°F (260-288°C). This will produce 58-60 HRC. For maximum toughness, double temper, 2 hours plus 2 hours, at temperatures above 950°F (510°C).

Reply

EN 10149-2 Grade S355MC thermomechanically rolled -

The thermomechanical rolled steel S355MC, mat. no. 1.0976, is used for cold formed components like vehicle frames, axles and special sections. Tempering > 580 deg. leads to an decrease of the strength of the thermomechanical treated material. The lowest application temperature amounts to - 20 deg.

Reply

S355 European Standard Steel - joostdevree.nl

S355 structural steel plate is a high-strength low-alloy European standard structural steel covering four of the six "Parts" within the EN 10025 – 2004 standard. With minimum yield of 50,000 KSI, it meets requirements in chemistry

Reply

Maximum allowable hardness A106/A516 Carbon Steel

Jan 28, 2014 · Maximum allowable hardness A106/A516 Carbon Steel. We had a fire in a gas station and soem vessels were exposed for several hours to the fire. Have no idea what the temperature may have been but > 600 degrees C. Does anybody know what the maximum allowable hardness is for the CS A106 /A516. The inspector is using Brinell hardness meter. Thanks

Reply

High-Strength Low-Alloy Steels - ASM International

High-Strength Low-Alloy Steels Introduction and Overview High-strength low-alloy (HSLA) steels, or microalloyed steels, are The chemical composition of a specific HSLA steel may vary for see Table 2. (b) If a single value is shown, it is a maximum unless otherwise stated. (c) Values may vary, or minimum value may exist, depending on

Reply

Engineering Bar Product Manual

B16 is a bolting specification for high temperature service. It is a heat treated chromium molybdenum vanadium (CrMoV) steel. The specification calls for minimum strength and maximum hardness levels. It is considered to be most suitable for components used at temperatures below 450°C (840°F).

Reply

HSLA steels - ArcelorMittal

Steels in the HSLA (High Strength Low Alloy) range are hardened by a combination of precipitation and grain size refining, resulting in high strength with low alloy content. This enhances weldability and choice of coatings, since these steels exhibit neither weld-zone softening nor grain coarsening. These grades are particularly suitable for structural components such as suspension systems

Reply

Air-Hardening Tool Steel McMaster-Carr

Choose from our selection of air-hardening tool steel, including over 750 products in a wide range of styles and sizes. In stock and ready to ship.

Reply

Contact us